NTS100

Compact Time Server: NTS100

The NTS100 is a compact Single Port NTP and/or PTP (IEEE1588 v2) Time Server that provides secure, accurate and reliable timing references for synchronizing enterprise networks.  In addition to robustness, features such as remote configuration, enhanced security, and capability to act as a PTP Grandmaster Clock, make the NTS100 a versatile synchronization solution for a wide range of network applications.

Key Features:

  • Single RJ45 port
  • Local configuration USB Port
  • PTP (IEEE 1588v2) Master/Slave function
  • UTC & LST with user defined DST options
  • Remote configuration
  • Security including password protection, user authentication & data encryption
  • Multi level password protection with custom configurable privilege settings
  • Complies with 61850-3

Input/Output Signals:

  • SNMP v1, v2c & v3
  • Proprietary MIB, USM MIB, C37.238 MIB
  • NTP/SNTP v3, v4 server operation, and basic SNTP client protocol for testing purposes
  • PTP IEEE 1588v2 (Supports Power Profile - C37.238, and Telecom Slave Profile - ITU G.8265.1)

Physical

Design:
Metal DIN-rail mountable case, with IP30 rating
Measurements: (L) 155 mm x (W) 110 mm x (H) 45 mm
Weight: 0.42 kg
LED Indicators:
Three LEDs indicate multiple statuses:
- Sync
- Alarm
- Power

GNSS Receiver

L1, C/A code, 32 Channel Parallel-tracking receiver
Frequency:
1598 Mhz
 
Acquisition (Sensitivity):
- 155 dBm
Tracking (Sensitivity): -160 dBm

Oscillator - TCXO

Holdover characteristics operating at 25°C :
- TCXO 1PPS drifts 0.55 ms over a 24 hour period.
- Drift rate: 7 ppb per second

Inputs & Outputs

Sync indication output: 200 V, 100 mA (Max)
USB 2.0 local configuration port: Type B, USB 2.0

RJ45 UTP Connector:

10/100 Mbps, Auto MDIx

Antenna connector:

BNC
100 mA drive power

Ethernet UTP Connection

Protocols supported:
 ARP, UDP, ICMP, TFTP, DHCP, SNMP, and BOOTP
NTP/SNTP: Stratum-1 NTP & SNTP time server, Multicast & Broadcast server capability, Optional MD5 authentication
Timing Accuracy: <100 ns to UTC
PTP (IEEE1588 v2) - GrandMaster
- Slave Default
- Power Profile (Full) - C37.238
- Telecom Slave Profile - ITU G.8265.1
- 1-step/ 2-step
- Layer 2 or Layer 3
- Peer to Peer delay
- End to End delay
- Multicast operation
- Accuracy <100 ns to UTC
   SNMP                                                                                   - v1, v2c & v3 support can be independently enabled
- Configurable v1, v2c community names & security groups
- Fully configurable via SNMP
- v3 User-based Security Module (USM) support - USM MIB support      
USM authentication methods                                       - MD5
- SHA                                                                         
USM privacy methods                  - DES
- AES   
Notifications                                                          - SNMP trap generation v1, v2c & v3
- SNMPv3 traps can be authenticated
Upgrades                                                      
Remote upgrades supported via Ethernet port

Isolation

Power to Antenna                                                    3.75 kV
Power to I/O                                                   
3.75 kV

Environmental & Electrical

Power supply:
48-250 Vdc (wide range supply)
Power drain: 5 W max
Operating Temperature:
-40 to +85 C
Humidity:
95% non-condensing

Compilance

The NTS100 passes the following tests: Applicable council directive according to:
- CE Compliance Low voltage directive EN60950-1
- EMC Directive EN61000-6-2, EN61000-6-4
- C22.2 No. 60950-1

Programmability

Customization is achieved using the windows based Tekron Configuration Tool, which is accessed via Ethernet/USB, allowing remote configuration.
User adjustable features include: - Multi-level access control
- Privacy & authentication methods equivalent to SNMP USM
- “Supervisor-mode” prevents non-approved changes
Timing & Synchronization: Worldwide daylight savings & local time configuration using either rule based or fixed date methods. Options that allow equipment checks prior to full installation and adjustable hold-over times to increase reliability in the case of poor GPS coverage. Adjustments to compensate for installation parameters such as delay of GPS signal through antenna cable.

 

Villámvédelmi készlet

The antenna lightning protection kit affords additional protection through the use of an impulse suppressor installed in the antenna lead-in coax cable. In the event of a lightning-derived high voltage surge occurring on the coaxial cable, the impulse suppressor activates, short-circuiting the cable directly to the protection ground. Kit contents (all components required to install lightning protection are included): - Impulse Suppressor - Self-amalgamating tape - 2 x N-type Male crimp style connectors to match antenna cable - Crimp Tool to match the above connectors (RG59).

Antenna tartó

The antenna mounting bracket is an adjustable 500mm powder-coated steel bracket for securely mounting the timing optimized antenna option.

Antenna kábel

High performance CNT-240 cable, factory-fitted with a TNC-type male connector at one end, and a SMA male connector at the other. Cables are available in standard 15, 30, or 60 meter options. Contact our sales team if you require other custom lengths.

Timing Optimized GPS/GLONASS Antenna

Dual GPS/GLONASS antenna radome that boasts exceptional out-of-band rejection, specifically designed for industrial/static timing environments. The antenna includes a pipe-mounting plinth that is designed to fit the antenna mounting bracket accessory.


Kapcsolat

Amennyiben bármely termékünk, szolgáltatásunk felkeltette érdeklődését, illetve ezekkel kapcsolatban kérdése, információ, tanácsadás iránti igénye lenne, az alábbi elérhetőségeken vegye fel velünk a kapcsolatot.

Cím

Mistral-Contact Kft.
1184 Budapest, József u. 29.

Térkép

Térkép

Gyártók oldala

Cégünk az alábbi gyártók képviseletét látja el Magyarországon

A PHP Error was encountered

Severity: Core Warning

Message: PHP Startup: Unable to load dynamic library 'gd2' (tried: /opt/plesk/php/7.4/lib/php/modules/gd2 (/opt/plesk/php/7.4/lib/php/modules/gd2: cannot open shared object file: No such file or directory), /opt/plesk/php/7.4/lib/php/modules/gd2.so (/opt/plesk/php/7.4/lib/php/modules/gd2.so: cannot open shared object file: No such file or directory))

Filename: Unknown

Line Number: 0

Backtrace: